|
|
|
Stone
Cutting Tools
Granite Edge Cutting Saw Blades
Marble
Edge Cutting Saw Blades
Granite Block Cutting Saw Blades
Marble
Block Cutting Saw Blades
Multi-Saw Blades
& Segments
Cross
Cutting Saw Blades
Horizontal
Cutting Saw Blades
Gangsaw Segments for Marble
Diamond
Wire Saw for Granite
Diamond
Wire Saw for Marble
Small
Diamond Saw Blades
Stone Grinding & Polishing Tools
Diamond
Abrasives for Granite
Diamond
Flexible Polishing Pads
Floor Polishing Pads
Abrasive Brush
Diamond
Grinding Cup Wheels
Diamond
Profile Wheels
Diamond Router Bits
Diamond Finger Bits
Polishing Wheels
Other Tools
Drill
Core Bits for Stone
Drill Core Bits for Concrete
Ceramic
Cutting Saw Blades
Bush Hammer
Diamond Hand Pads
Kinds
of Diamond Segments
|
|
|
Diamond Wire Saw for Marble Quarries
Diamond wires used for marble quarries
which can vastly improve efficiency and reduce the waste of quarry
resource vastly. It is benefit in environmental protection and works
safety.
|
Diameter
(mm) |
Fitting |
Beads/M |
Material
type |
Sawing
speed
(㎡/h) |
Lifetime
(㎡/m) |
Liner
speed
(m/s) |
remark |
|
Φ11 |
Spring
Plastic |
28/30/32
32 |
Class
A
White Crystalline
Travertine |
10-20 |
30-55 |
35-40 |
Beads
Sinterd |
|
Spring
Plastic |
28/30/32
32 |
Class B
Compact |
8-16 |
15-35 |
33-38 |
Beads
Sinterd |
|
Spring
Plastic |
28/30/32
32 |
Class
C-D
Coloured abrasive |
5-8 |
10-25 |
30-35 |
Beads
Sinterd |
|
Φ11
Φ10.5 |
Spring
Plastic |
28/30/32
32 |
A---D |
12-25 |
10-30 |
30-35 |
Beads
Electroplated |
We can make
HRB 80-95 hardness bond and the different diamond formula according to
the type of material.
Diamond
wire Saw for marble profiling cutting
The advantage of the diamond wire for
profiling is stable cutting, high performance, smooth cutting face,
and accurate of processing ect.
|
Diameter
(mm) |
Fitting |
Beads/M |
Material
type |
Sawing
speed
(mm/min) |
Lifetime
(m2/m) |
Liner
speed
(m/s) |
|
Φ8.8
Φ8.2 |
Plastic |
32 |
Class A
Class B
Class C-D |
20-35
15-25
10-20 |
30-50
25-40
20-30 |
30-40
28-35
28-30 |
Note:The sawing speed is calculated by sawing depth (mm) per minute
Recommendations:
1. The rotation of the wire should be regularly checked
2. The beads wear profile should be regularly inspected
3. The connections should be changed whenever excessively high wear of
the adjacent beads is noted and whenever it is necessary to apply pretorsion to the cable
4. The cable tension is set to 250-300kg(4-5mmdiameter cable)
5. Adiust the liner speed of the wire to the material being sawn:
Granite class 1—2: 25—30m/s
Granite class 3—4: 22—26m/s
Granite class 5: 20—24m/s
Marble: 30—35m/s
Abrasive stone: 30—35m/s
6. During the sharpening of a new wire ,the liner speed must be reduced
by 2-3m/s
7. Water spraying between 15-25L/min
Diamond
Wire Saw for Marble squaring and cutting
1．The wire allows significantly greater
sawing heights than large discs.
2．Thinner cutting width, and more precise .
3．By virtue of its reliability, adjust the cutting techniques
according to different stone material.
4．Noise nuisance generated by diamond wire saw is significantly less
than produced by other sawing techniques.
|
Diameter
(mm) |
Fitting |
Beads/M |
Material
type |
Sawing
speed
(m2/h) |
Lifetime
(m2/m) |
Liner
speed
(ms/s) |
remark |
|
Φ10 |
Plastic |
32 |
Class
A:
Crystalline and travertine
Class B:
Compact
Class C-D:
Coloured abrasive |
5-8
3-5
2-5 |
30-70
20-50
15-30 |
30-35
30-35
26-30 |
Sintered |
|
Φ10.5 |
Plastic |
32 |
|
Φ11 |
Plastic |
32 |
|
Φ11 |
Plastic |
32 |
Mixed
marble |
5-10 |
20-40 |
30-35 |
electroplate |
 |
|
|
